Three layers of grit filter-manufacture,factory,supplier from China

When the filter is working normally, the pressurized water flows into the tank from the water inlet and reaches the filter layer evenly. When the water flows through the filter layer, the impurities are filtered and retained. There is a water trap with a valve at the bottom of the filter, and the filtered water is collected evenly and then flows out of the filtering equipment.With the continuous accumulation of impurities in the filter layer, the water flow loss continues to increase.

1. Check the condition of the pressure gauge to see if it is working properly.2. Check the pressure values of pressure gauge 1 and pressure gauge 2, when the difference between the pressure values of the two pressure gauges exceeds 0.02GP, clean the filter screen.

Precise filtration: Filter discs with exceptional precisions may be selected in step with the water requirements. There are 20 microns, 55 microns, one hundred microns, 130 microns, two hundred microns, 400 microns and other specifications, and the filtration ratio is extra than 85%.Thorough and efficient backwashing: Because the filter pores are completely opened during backwashing, and the centrifugal jet effect is added, the cleaning effect that other filters cannot achieve can be achieved.

Fertilization flow of three-channel fertilizer applicator:1. First of all, the dissolved fertilizer solution into the fertilizer pot, open the main pump, through the regulating valve will be filled with water, closed water injection valve (the process of irrigation valve can always open) . When fertilizing, the “Time knob”in the control cabinet is used to adjust the time of fertilizing, the pump starts, the fertilizer in the tank is pumped into the main pipeline water by the pump, and the fertilizing is finished at the same time.

The stack clean out is composed of a hard and fast of plates with grooves on each sides. the intersection point shaped with the resource of the rims of the grooves can intercept the solids in the water.

1. The effective utilization rate of water is high. Under the condition of drip irrigation, the irrigation water wets part of the soil surface, which can effectively reduce the ineffective evaporation of soil water. At the same time, because drip irrigation only moistens the soil near the roots of the crops, and the soil moisture content in other areas is low, it can prevent the growth of weeds. Third, the drip irrigation system does not generate ground runoff, and it is easy to grasp the precise watering depth, which is very water-saving.2.

The pipe joint with three openings is called tee pipe. Tee pipe is widely used in the pipe network conveying liquid and gas. Due to different conveying media, the material of tee pipe is divided into: cast copper, cast aluminum, plastic, cast iron, cast steel, glass, etc. tee is also widely used.Introduction:As the name suggests, there are three openings, i.e. one in and two out, or two in and one out. It is a kind of chemical pipe fittings, T-shaped and Y-shaped. It has equal diameter nozzle and reducing nozzle. It is used for the collection of three identical or different pipelines.

Often preferred by panorama gardeners and terrific for plants that don’t do nicely with water on their leaves (like tomatoes and eggplants), point-source emitters are non-adjustable, preset nozzles that distribute a fixed amount of water to a plant in line with hour. they’re terrific to be used with “satellite” vegetation in planters and striking baskets, as well as sensitive vegetables.

Components used in drip irrigation (listed in order from water source) include: Pump or pressurized water source. Water filter(s) or filtration systems: sand separator, Fertigation systems (Venturi injector) and chemigation equipment (optional) Backwash controller (Backflow prevention device)

1. The location of the water source and the head hub is generally selected in the middle of the plot, and the location is higher.2. When irrigating, the position of the water inlet is high, and ensure that the position of the drain well is at a lower position.3. Generally, the water delivery and distribution pipelines of the drip irrigation system can be divided into three-stage pipelines: main pipe, branch pipe, and capillary (drip irrigation tape (pipe)), and some systems are equipped with branch pipes. The pipelines at all levels are arranged vertically with their superior pipelines.4.

Performance characteristics:The structure design is reasonable, when the water pressure is small, it can also irrigateIt is suitable for irrigation of fruit tree, shrub nursery, narrow lawn and other crops, irrigation and cooling of greenhouse cropsThe rotary sprinkler sprays in rain formThe spraying diameter is 6mCommon overall performance trends:The structure layout is cheap, whilst the water strain is small, it can also irrigateIt is appropriate for irrigation of fruit tree, shrub nursery, narrow garden and special flora, irrigation and cooling of greenhouse plantsThe rotary sprin

Micro-spray TapeMicro-spray Tape are useful devices which can make the most of a low-pressure drip irrigation system. They install along taller vegetation or are used to hit a few flora with extra water needs whilst leaving much less-needy plant life by myself. They’re designed with progressed spray-range over other emitter-kinds with the identical strain.