Plastic filter-manufacture,factory,supplier from China

1. Check the condition of the pressure gauge to see if it is working properly.2. Check the pressure values of pressure gauge 1 and pressure gauge 2, when the difference between the pressure values of the two pressure gauges exceeds 0.02GP, clean the filter screen.

When the filter is working normally, the pressurized water flows into the tank from the water inlet and reaches the filter layer evenly. When the water flows through the filter layer, the impurities are filtered and retained. There is a water trap with a valve at the bottom of the filter, and the filtered water is collected evenly and then flows out of the filtering equipment.With the continuous accumulation of impurities in the filter layer, the water flow loss continues to increase.

Precise filtration: Filter discs with exceptional precisions may be selected in step with the water requirements. There are 20 microns, 55 microns, one hundred microns, 130 microns, two hundred microns, 400 microns and other specifications, and the filtration ratio is extra than 85%.Thorough and efficient backwashing: Because the filter pores are completely opened during backwashing, and the centrifugal jet effect is added, the cleaning effect that other filters cannot achieve can be achieved.

Subsurface drip irrigation structures follow water immediately to the crop root quarter thru buried plastic tapes with embedded emitters.The essential advantage of us structures is their water-use efficiency, in comparison to sprinkler irrigation or furrow irrigation structures. Because drip tapes are buried at approximately 12 inches beneath floor floor (this will range relying on soil kind and crop) and the soil floor remains dry, water loss because of evaporation and runoff are minimized.Another massive benefit of us is its flexibility to irrigate irregular-fashioned fields.

The stack clean out is composed of a hard and fast of plates with grooves on each sides. the intersection point shaped with the resource of the rims of the grooves can intercept the solids in the water.

Components used in drip irrigation (listed in order from water source) include: Pump or pressurized water source. Water filter(s) or filtration systems: sand separator, Fertigation systems (Venturi injector) and chemigation equipment (optional) Backwash controller (Backflow prevention device)

The pipe joint with three openings is called tee pipe. Tee pipe is widely used in the pipe network conveying liquid and gas. Due to different conveying media, the material of tee pipe is divided into: cast copper, cast aluminum, plastic, cast iron, cast steel, glass, etc. tee is also widely used.Introduction:As the name suggests, there are three openings, i.e. one in and two out, or two in and one out. It is a kind of chemical pipe fittings, T-shaped and Y-shaped. It has equal diameter nozzle and reducing nozzle. It is used for the collection of three identical or different pipelines.

Drip irrigation belt is the core product of drip irrigation system and plays a decisive role in the operation effect of drip irrigation system. It is praised as an efficient water-saving equipment in arid and water-deficient areas, which can effectively improve the utilization rate of water and fertilizer and achieve rational planting of water saving and energy saving. Drip irrigation belt is to use plastic pipes to pass water (liquid fertilizer or pesticide, etc.) through a capillary tube with a diameter of about 16mm.

Of course, while used on the perfect crop, drip irrigation has some of key benefits:It may function at a decrease strain;In case you are developing a crop like pumpkin and watermelon with a extensive spacing, you don’t waste water on areas where there's no root device to take it up;It is good for vegetation in which wetting the leaves can motive disease. this makes it the favoured system for tomatoes and crops grown in tunnels;It's miles important when plastic mulch is used to cowl the soil.Dripper tubes come in various forms.

FeaturesColor: As the pix shown.Material: ABS, plastic.Premium quality - 3 arm + ABS plastic rotary garden sprinkler with Ground Rod.Effective water sprinkler irrigation machine - patented layout of water-saving tool may be centered to keep water maximum with the aid of using adjusting the water density, length and scope.Easy use - join water joint to the connector and tap.Long spray distance - as much as 26ft-32.8ft distance with worldwide general pipes.Different spray direction - direct or forty five degree.Spraying distance: upward 2.5-3m, lateral 4-5m Connection length: half of Inch M

Compared with the dripper, the most obvious feature of the pressure-compensated dripper is:1. The pressure compensation dripper can make the elastic silicone sheet change the section of the water outlet with the help of water conservancy pressure, automatically adjust the flow rate, and make the water output uniform;2. The pressure compensation performance is strong, and the automatic control water dispenser is the best choice. It is especially suitable for undulating terrain, unbalanced system pressure and need to increase capillary.How to choose a pressure compensation dripper?1.

Based on the definition and connotation of the above-mentioned water-saving products, it can be divided into the following categories from the principles and approaches of water-saving:(1) Products that directly improve the use efficiency of water resourcesIt is a water-consumable product, and it can reduce water consumption compared to similar products under the condition of fulfilling the same function.(2) Products that reduce the loss of water resources and prevent pollutionIn the process of use, it does not consume water resources, but it can ensure that water resources are not lost and po