lock female bypass valve-manufacture,factory,supplier from China

Commands for use: Mainly used for capillary head give up manage (the right give up of the pull ring is hooked up to a 16mm drip tape, that is fixed through the pull ring; the left give up is hooked up to the water shipping most important pipe, which may be used for pe pipes (wall thickness more than 1mm), water transport tape or use with matching rubber bands , connect to pvc pipe.)Product introduction: the pull-ring pass switch is a generally used drip irrigation transfer.

Fertilization flow of three-channel fertilizer applicator:1. First of all, the dissolved fertilizer solution into the fertilizer pot, open the main pump, through the regulating valve will be filled with water, closed water injection valve (the process of irrigation valve can always open) . When fertilizing, the “Time knob”in the control cabinet is used to adjust the time of fertilizing, the pump starts, the fertilizer in the tank is pumped into the main pipeline water by the pump, and the fertilizing is finished at the same time.

1. Establish a drip irrigation system first. The length and depth of the pipeline system should be designed according to basic conditions such as topography, soil texture, crop planting conditions, and water sources. So that the integration of water and fertilizer can play the greatest efficiency.2. The fertilization system should be designed for quantitative fertilization in the field, including the location, capacity, outlet, fertilization pipeline, distributor valve, water pump and fertilizer pump of the reservoir and fertilizer pool.3.

When the filter is working normally, the pressurized water flows into the tank from the water inlet and reaches the filter layer evenly. When the water flows through the filter layer, the impurities are filtered and retained. There is a water trap with a valve at the bottom of the filter, and the filtered water is collected evenly and then flows out of the filtering equipment.With the continuous accumulation of impurities in the filter layer, the water flow loss continues to increase.

This product is used when the drip irrigation system uses tape as the main pipeline. The branch water source, the main pipeline (soft belt) is connected with the drip irrigation belt, so that the water in the main pipeline (soft belt) flows into the drip irrigation belt separately.Use a punching machine (diameter 14mm) to make holes on the side of the soft water belt, then screw the tee into the hole of the soft water belt, tighten the nut to fix the bypass on the soft water belt, and connect the soft water belt to the other side of the drip irrigation belt.

Pipe failure in long-term applications is characterised by creep crack initiation and creep crack growth. Both can be determined by fracture mechanics-based tests of the pipe materials. Nowadays, several accelerated tests are available: Considering new fiber composite polyethylene (pe) substances are contemplated for use by means of fuel industry, a chief assignment is to carry out a computational evaluation for the cracked and uncracked pipes. That is completed using a completely unique finite detail code pfrac.

The arrangement and installation of the dripping belt: The branch pipes are arranged according to the row direction of grape planting. Generally, the branch pipe is arranged in the middle of the grape row, and the dripping belt is arranged according to the spacing of the grapes. If the planting row is too long, it can be divided into two groups from the middle part of the vineyard, and two valves can be installed to send the water to both sides respectively to implement group irrigation.Precautions for drip irrigation1. Prevent the drip hole from clogging.

Pressure CompensationThe amount of pressure that flows through a drip irrigation system can fluctuate, depending on hose length and garden bed elevation, among other factors. This can cause emitters to flow differently than designed, with more or less water flow depending on pressure.To combat this, the best drip irrigation system emitters are pressure compensating by design. They’ll emit the same amount of water regardless of the pressure at their inlet (where they attach to the main hose).

Based on the definition and connotation of the above-mentioned water-saving products, it can be divided into the following categories from the principles and approaches of water-saving:(1) Products that directly improve the use efficiency of water resourcesIt is a water-consumable product, and it can reduce water consumption compared to similar products under the condition of fulfilling the same function.(2) Products that reduce the loss of water resources and prevent pollutionIn the process of use, it does not consume water resources, but it can ensure that water resources are not lost and po

Offer amazing insulation. tube protects the, metallic, cable, wood and and many others towards to quick circuit, corrosion, oxidation, decay, abrasion, fracture and and many others. software location; can used for sealing reason of power, facts, telecom cables and automotive, digital, plane, train, subway, port etc.

The Hose Tubing is crafted from new PVC material, long lasting non-poisonous and eco-friendly.Flexible: Industry main flexibility permits tighter turns with fewer elbows for fast, clean set up in garden, flower bed, floor cowl or different landscaped regions.Function: Use as the primary line in a small Drip irrigation gadget or to department off from large tubing to micro-watering gadgetCompatible with maximum manufacturers of 16mm pipe Barbed Fittings, Spot Watering Emitters, Micro-Bubblers, Misters and Sprays.Perfect for small, slender and tight planting regions, in addition to regions with

FeaturesColor: As the pix shown.Material: ABS, plastic.Premium quality - 3 arm + ABS plastic rotary garden sprinkler with Ground Rod.Effective water sprinkler irrigation machine - patented layout of water-saving tool may be centered to keep water maximum with the aid of using adjusting the water density, length and scope.Easy use - join water joint to the connector and tap.Long spray distance - as much as 26ft-32.8ft distance with worldwide general pipes.Different spray direction - direct or forty five degree.Spraying distance: upward 2.5-3m, lateral 4-5m Connection length: half of Inch M