Irrigation pull ring soft belt bypass-manufacture,factory,supplier from China

The pull ring straight through is used for the connection between drip irrigation tape and drip irrigation tape. Through the reasonable use of pull ring straight through, some shorter drip irrigation tapes can be reused, saving materials and reducing the project cost.Instructions: when in use, insert the pull ring straight through into the drip irrigation tape, and then use the pull ring to lock the drip irrigation tape. The operation method on the other side is the same.

The pull ring plug of drip irrigation tape is a fitting used with drip irrigation tape. It is used for the end sealing of drip irrigation tape, which plays a role of flow closure.Specification and model: 16mm, PE materialUsage:Cut the end of drip irrigation tape with scissors and insert it between the blue pull ring and black part of the pipe fitting.Pull the blue pull ring outward and clamp the drip irrigation tape tightly.

Instructions for use: used for the connection and front-end control of the water delivery belt and the drip irrigation belt (one end of the valve is connected to a 16mm drip irrigation belt, which is fixed by a screw lock; the other end is connected to the main water delivery belt)How to use: First use a hole punch (14mm in diameter) to punch holes on the side of the soft water belt, then rotate the bypass valve of the drip irrigation belt into the hole of the soft belt, tighten the nut to fix the bypass on the soft water belt, and on the other side Just connect the drip tape.

Usage: first, use special puncher to punch holes on the side of soft water tape, then rotate the bypass valve of the product into the hole of soft tape, tighten the screw to fix the bypass valve on the soft water tape, and connect the drip irrigation tape on the other side.

Instructions for use: Mainly used for capillary head end control (the right end of the pull ring is connected to a 16mm drip tape, which is fixed by the pull ring; the left end is connected to the water delivery main pipe, which can be used for PE pipes (wall thickness greater than 1mm), water delivery tape or use with matching rubber bands , Connect with pvc pipe.)Product introduction: The pull-ring bypass switch is a commonly used drip irrigation switch.

The drip irrigation belt snap tee has the following advantages: 　　1. There are internal parts such as locking hoop, stepped ring seal ring, etc. The nuts on both sides can be disassembled for assembly and use, which improves the product reuse rate. And the product design is scientific and reasonable, the pipe fittings have high strength, good sealing performance, and no water leakage. 　　2. The drip irrigation belt positive female snap tee is easy to install and use, easy to disassemble, flexible, easy to recycle, beautiful and practical.

Product features: soft tape bypass valve has its own valve, which can control and adjust the flow of each drip irrigation tape at will.Precautions for installation: 1. mainly used for connection of main water tape, PE water tape(wall thickness 0.6-1.6mm), etc.2.The fittings of this specification are connected between the soft drip irrigation tapes with inner diameter of 16mm.

Product introduction: the pull ring bypass switch is a common drip irrigation switch, one end of which is connected with the main water tape or PE pipe, and the other end is connected with the drip irrigation tape, so as to achieve the effect of controlling the water flow in the rear section of the valve.Instructions for use: it is mainly used for controlling the head end of the capillary (the right end of the pull ring is connected with a 16mm drip irrigation tape, which is fixed by the pull ring; The left end is connected with main water delivery pipe, which can be used for PE pipe (wal

Purpose: the drip irrigation system uses the product when the tape is the main pipe. Branch water source, the main pipeline (soft tape) is connected with drip irrigation tape, so that the water in the main pipeline (soft tape) flows into the drip irrigation tape respectively.Usage: use a puncher (14mm in diameter) to make a hole on the side of the soft water tape, and then rotate the three-way into the soft tape hole, tighten the nut to fix the bypass on the soft water tape, and connect the drip irrigation tape on the other sideParameters:Model:16mmMaterial: PE plastic

16mm double lock-nut bypass valve and double thread bypass switch are made of high-quality engineering plastics. The products are of high quality and durable. This kind of drip irrigation bypass switch adopts double thread form with tight connection, good water locking effect and no water leakage.Installation steps: drill 8 mm hole in the main water supply pipe, insert the bypass valve, rotate the lock-nut, and connect the 16mm end with the drip irrigation tape. Tip: after drilling holes on PE pipe and plastic hose, directly insert and install it.

Product features: scientific design, high strength, good sealing, convenient connection, easy disassembly, strong flexibility, easy recycling, and beautiful appearance. It is made of engineering plastics and has a long service life.

The drip irrigation belt uses a plastic pipe (drip irrigation pipe lead) to send water through the orifice or dripper on the capillary tube with a diameter of about 10mm to the root of the crop for local irrigation. It is a dripper or drip irrigation belt with a very small outlet orifice, which drips water evenly and slowly into the soil near the roots of the crops.1. The built-in dripper has its own filter window, which has good anti-blocking performance.2. Turbulent flow channel design. Water evenly.3. The dripper and pipeline have strong integrity,4.

Lock-nut bypass parameterNameLarge hole lock-nut bypassSpecifications16-16mm  12-16mmPackageBaggedQuantity2000 pieces/ bagSales modelWholesale, agencyMaterialSpecial materials have strong aging resistanceApplicable conditionsThe main pipes are PE irrigation pipe and PVC irrigation pipe

Purpose: it is usually used in drip irrigation system, when PE soft tape is used as main (branch) pipe, and the soft tape three-way is used as water separation device to connect with drip irrigation tape. That is, the irrigation system uses soft tape as low-pressure water transmission pipeline, and uses soft tape three-way to connect with soft tape , and then connects with drip irrigation tape through the reversed lock-nut on the soft tape three-way, and supplies water to drip irrigation tape of both sides, thus forming rapid and accurate irrigation of water source.

Drip irrigation : The inlaid drip irrigation pipe is an integrated drip irrigation pipe with a cylindrical dripper embedded on the inner wall of the pipe. The dripper is assembled on the inner wall of the pipe while producing the pipe, which is easy to install and use.Classification1. According to the water outlet method, it is divided into:Pressure Compensated Drip Irrigation Pipes and Non-Pressure Compensated Drip Irrigation Pipes2. According to the structure can be divided into:In-line drip irrigation pipe and inter-pipe drip irrigation pipeapplicationApplicable conditions:1.

There are two types of drip irrigation tape lock-nut bypass produced by our factory, one is 12-16mm reversed lock bus bypass, the other is 16-16mm reversed lock-nut bypass. Generally, users call this kind of reversed lock-nut bypass as drip irrigation tape lock-nut bypass. 16-16mm lock-nut bypass is also called large hole lock-nut bypass or large body lock-nut bypass. Because both ends are 16mm diameter, this large hole lock-nut bypass is a kind of bypass that is more commonly used in lock-nut pipe fittings.

Product features:It is made of new engineering plastics, with aging-resistant process and materials, long service life, mainly supporting export products.Scientific design, high strength, good sealing, convenient connection, easy disassembly, strong flexibility, easy recycling, beautiful appearance.It is mainly applicable to the irrigation of vegetables, fruit trees, shrubs, nurseries and other ground crops, and can be used for tree crown cooling and tree frost preventionSpraying and drip irrigation of plant cooling, urban environmental protection, lawn and other aspects.Instruc

Features: drip irrigation tape can connect main pipe (water tape) instantly. The bypass has its own valve, and the water flow can be adjusted at will.Precautions for installation:1.It is mainly used for connection of main water tape, PE water tape(wall thickness 0.7-3.0mm), etc.

Performance characteristics: wider water path, the water flow is in a turbulent state and there are multiple inlets into the labyrinth, which has strong anti-clogging ability; the main pipeline on the ground is a black water delivery tape or pipe array, which is suitable for drip irrigation in greenhouses and fields.Technical parameterPipe diameter [mm)Distance between emitters (mm)Pressure (Mpa)Flow rate (L/H)Length of laying (m)Diameter 20300（adjustable)0.02 -0.082、3、4≤150Diameter 16300（adjustable)0.02 -0.082、3、4≤100Diameter 12300 (adjustable

The pressure compensation drip irrigation pipe is made of high-density PE pipe with improved nanotechnology and built-in pressure compensation emitter. It is suitable for complex terrain and has the characteristics of good uniformity, strong anti-clogging ability and long service life.The commonly used model of pressure compensation drip irrigation pipe is Φ16. The distance between the emitters is 300mm (200), the wall thickness is 0.6mm, 0.8mm and 1.0mm.

Suitable for spray irrigation and drip irrigation 16mm PE pipePurpose: used for 16mm PE pipe connecting PE main pipe, PVC main branch bypass joint switch

Installation and usage: the product is used in the project of PE small pipe or drip irrigation pipe. Compared with the traditional PE socket straight through and bypass, the advantages are that the user can adjust the switch of each irrigation pipe tape and increase the controllability of the system.through is made of new engineering plastics, with beautiful appearance, strong anti-aging performance, low cost and long service life. Scientific design, convenient connection, easy disassembly, strong flexibility, good sealing, beautiful and practical, and easy to install and use, easy to recycle.

The built-in patch drip irrigation tape has the following characteristics:The built-in patch drip irrigation tape has many kinds of drip hole spacing for customers to choose, and can customize drip irrigation tape with different plant spacing for customers, so as to ensure that the drip irrigation tape meets the requirements of customers for all planting spacing.The outer diameter of the product is 16mm, and the wall thickness is divided into three types: 0.2/0.3/0.4mm (normal working pressure is 0.08MPa-0.1MPa, and the flow rate of emitter is 2L/h). It can b