7-hole Adjustable Emitter-manufacture,factory,supplier from China

The red adjustable flow dripper can also be called the 8-hole red little red cap dripper. The 8-hole red little red cap dripper can be adjusted to sprinkle, drip, and close. Adjust to the left to close, adjust to the right to adjust the water flow. The water outlet distance is determined according to the water supply pressure.

Suitable occasions: suitable for various terrain and crops, especially in irrigation area with large slope fluctuation; Suitable for the case where the laying length of drip irrigation pipe is large; Suitable for the emitter spacing changes; When the system pressure is unstable.

Pressure compensation range: 0.08-0.4MPa, emitter specification and flow: 4L/h, 8L/hPerformance characteristics:When the system pressure changes from 0.08 to 0.35Mpa, the flow of the emitter remains unchanged, and the uniformity of irrigation can reach more than 98%.Features of use:The installation on the construction site is suitable for any spacing of crops. PE water pipe can be buried below the ground.

Pressure compensation range: 0.08-0.4MPa, emitter specification and flow: 4L/h, 8L/hPerformance characteristics:When the system pressure changes from 0.08 to 0.35Mpa, the flow of the emitter remains unchanged, and the uniformity of irrigation can reach more than 98%.Features of use:The installation on the construction site is suitable for any spacing of crops. PE water pipe can be buried below the ground.

Drip irrigation dripper characteristics1. Silicone sheet inside the dripper can change the section of the water outlet, realize the effect of stable water flow and flow regulation. It can be installed on fruit trees, saplings and forest trees with a relatively long distance, and the distance between the drippers can be adjusted arbitrarily according to the distance between crops. Suitable for various terrains such as plains, mountains, plateaus, terraces, hills, etc.2. The dripper has a small volume, so it is easy to install.

Lock-nut bypass parameterNameLarge hole lock-nut bypassSpecifications16-16mm  12-16mmPackageBaggedQuantity2000 pieces/ bagSales modelWholesale, agencyMaterialSpecial materials have strong aging resistanceApplicable conditionsThe main pipes are PE irrigation pipe and PVC irrigation pipe

Set combination  Multiple combinations can meet your various needsAOne-outlet two small straight drip arrow + single hook  One 4/7 to 3/5 single hookOne 3/5 three-way water separatorTwo 50cm3/5PVC capillaries  Two small straight drip arrowsBOne-outlet two small straight drip arrows + current stabilizer One 2L, 4L, 8L current stabilizerOne 3/5 three-way water separatorTwo 50cm3/5PVC capillaries Two small straight drip arrowsCOne-outlet two big straight drip arrow + single hook  One 4/7 to 3/5 single hookOne 3/5 three-way

Performance characteristics: wider water path, the water flow is in a turbulent state and there are multiple inlets into the labyrinth, which has strong anti-clogging ability; the main pipeline on the ground is a black water delivery tape or pipe array, which is suitable for drip irrigation in greenhouses and fields.Technical parameterPipe diameter [mm)Distance between emitters (mm)Pressure (Mpa)Flow rate (L/H)Length of laying (m)Diameter 20300（adjustable)0.02 -0.082、3、4≤150Diameter 16300（adjustable)0.02 -0.082、3、4≤100Diameter 12300 (adjustable

Set combination Multiple combinations can meet your various needsAOne-outlet three small straight drip arrow + single hook  One 4/7 to 3/5 single hookOne 3/5 four-way water separatorThree 50cm3/5PVC capillaries  Three small straight drip arrowsBOne-outlet three small straight drip arrows + current stabilizer One 2L, 4L, 8L current stabilizerOne 3/5 four-way water separatorThree 50cm3/5PVC capillariesThree small straight drip arrowsCOne-outlet three big straight drip arrow + single hook  One 4/7 to 3/5 single hookOne 3/5 four-way&

The built-in patch drip irrigation tape has the following characteristics:The built-in patch drip irrigation tape has many kinds of drip hole spacing for customers to choose, and can customize drip irrigation tape with different plant spacing for customers, so as to ensure that the drip irrigation tape meets the requirements of customers for all planting spacing.The outer diameter of the product is 16mm, and the wall thickness is divided into three types: 0.2/0.3/0.4mm (normal working pressure is 0.08MPa-0.1MPa, and the flow rate of emitter is 2L/h). It can b

16mm double lock-nut bypass valve and double thread bypass switch are made of high-quality engineering plastics. The products are of high quality and durable. This kind of drip irrigation bypass switch adopts double thread form with tight connection, good water locking effect and no water leakage.Installation steps: drill 8 mm hole in the main water supply pipe, insert the bypass valve, rotate the lock-nut, and connect the 16mm end with the drip irrigation tape. Tip: after drilling holes on PE pipe and plastic hose, directly insert and install it.

The pressure compensation drip irrigation pipe is made of high-density PE pipe with improved nanotechnology and built-in pressure compensation emitter. It is suitable for complex terrain and has the characteristics of good uniformity, strong anti-clogging ability and long service life.The commonly used model of pressure compensation drip irrigation pipe is Φ16. The distance between the emitters is 300mm (200), the wall thickness is 0.6mm, 0.8mm and 1.0mm.

Usage: first, use special puncher to punch holes on the side of soft water tape, then rotate the bypass valve of the product into the hole of soft tape, tighten the screw to fix the bypass valve on the soft water tape, and connect the drip irrigation tape on the other side.

Purpose: the drip irrigation system uses the product when the tape is the main pipe. Branch water source, the main pipeline (soft tape) is connected with drip irrigation tape, so that the water in the main pipeline (soft tape) flows into the drip irrigation tape respectively.Usage: use a puncher (14mm in diameter) to make a hole on the side of the soft water tape, and then rotate the three-way into the soft tape hole, tighten the nut to fix the bypass on the soft water tape, and connect the drip irrigation tape on the other sideParameters:Model:16mmMaterial: PE plastic

Set combination  Multiple combinations can meet your various needsAOne-outlet four big straight drip arrow +current stabilizerOne 2L, 4L, 8L current stabilizerOne 3/5 five-way water separatorFour 50cm3/5PVC capillaries Four big straight drip arrowsBOne-outlet four curved drip arrows + single hook  One 4/7 to 3/5 single hookOne 3/5 five-way water separatorFour 50cm3/5PVC capillaries  Four curved drip arrowsCOne-outlet four curved drip arrows + current stabilizer One 2L, 4L, 8L current stabilizerOne 3/5 five-way water sep

There are two types of drip irrigation tape lock-nut bypass produced by our factory, one is 12-16mm reversed lock bus bypass, the other is 16-16mm reversed lock-nut bypass. Generally, users call this kind of reversed lock-nut bypass as drip irrigation tape lock-nut bypass. 16-16mm lock-nut bypass is also called large hole lock-nut bypass or large body lock-nut bypass. Because both ends are 16mm diameter, this large hole lock-nut bypass is a kind of bypass that is more commonly used in lock-nut pipe fittings.

Instructions for use: used for the connection and front-end control of the water delivery belt and the drip irrigation belt (one end of the valve is connected to a 16mm drip irrigation belt, which is fixed by a screw lock; the other end is connected to the main water delivery belt)How to use: First use a hole punch (14mm in diameter) to punch holes on the side of the soft water belt, then rotate the bypass valve of the drip irrigation belt into the hole of the soft belt, tighten the nut to fix the bypass on the soft water belt, and on the other side Just connect the drip tape.

 It is suitable for PE water supply pipe and PVC water supply pipe as the main pipe of drip irrigation. The branch pipe is suitable for 16mm PE coil pipe, 16 drip irrigation pipe, micro-spray irrigation 16 capillary pipe 16 PE pipe, etc.Installation steps: drill 8 mm hole in the main water supply pipe, insert the bypass valve, rotate the lock-nut, and connect the 16mm end with the drip irrigation tape. Tip: after drilling holes on PE pipe and plastic hose, directly insert and install it.

Model: Φ16mmMaterial: PEProduct advantages and characteristics:1.Scientific design, compact size, light weight, good sealing and interchangeability.2.Simple structure, convenient operation, quick connection and disassembly, strong flexibility, easy to recycle, beautiful and practical.3.Stable chemical properties, excellent performance, good cold-resistance, anti-aging, long service life.4.Compact size, light weight, good sealing and interchangeability.5.It is suitable for various working conditions and widely used in various media such as gas, liquid, powder, etc.

Precise filtration: Filter discs with different precisions can be selected according to the water requirements. There are 20 microns, 55 microns, 100 microns, 130 microns, 200 microns, 400 microns and other specifications, and the filtration ratio is greater than 85%.Thorough and efficient backwashing: Because the filter pores are completely opened during backwashing, and the centrifugal jet effect is added, the cleaning effect that other filters cannot achieve can be achieved.

Use and maintenance instructions1. Check the condition of the pressure gauge to see if it is working properly.2.

Purpose: it is usually used in drip irrigation system, when PE soft tape is used as main (branch) pipe, and the soft tape three-way is used as water separation device to connect with drip irrigation tape. That is, the irrigation system uses soft tape as low-pressure water transmission pipeline, and uses soft tape three-way to connect with soft tape , and then connects with drip irrigation tape through the reversed lock-nut on the soft tape three-way, and supplies water to drip irrigation tape of both sides, thus forming rapid and accurate irrigation of water source.

Product introduction: the pull ring bypass switch is a common drip irrigation switch, one end of which is connected with the main water tape or PE pipe, and the other end is connected with the drip irrigation tape, so as to achieve the effect of controlling the water flow in the rear section of the valve.Instructions for use: it is mainly used for controlling the head end of the capillary (the right end of the pull ring is connected with a 16mm drip irrigation tape, which is fixed by the pull ring; The left end is connected with main water delivery pipe, which can be used for PE pipe (wal

Features: good material, anti-aging, automatic drip irrigation pipe can improve economic benefits, smooth anti-aging inner wall, high impact strength and long service life. Anti-solarization, anti-aging, durability, high gloss, high quality, good corrosion resistance.Good toughness, strong adaptability to terrain, easy laying, long service life, more than 8 years naked on the ground. The connection is convenient, and there are special fast connection fittings.