The pull ring plug of drip irrigation tape is a fitting used with drip irrigation tape. It is used for the end sealing of drip irrigation tape, which plays a role of flow closure.Specification and model: 16mm, PE materialUsage:Cut the end of drip irrigation tape with scissors and insert it between the blue pull ring and black part of the pipe fitting.Pull the blue pull ring outward and clamp the drip irrigation tape tightly.
Contact Now
The pull ring straight through is used for the connection between drip irrigation tape and drip irrigation tape. Through the reasonable use of pull ring straight through, some shorter drip irrigation tapes can be reused, saving materials and reducing the project cost.Instructions: when in use, insert the pull ring straight through into the drip irrigation tape, and then use the pull ring to lock the drip irrigation tape. The operation method on the other side is the same.
Contact Now
Purpose: the drip irrigation system uses the product when the tape is the main pipe. Branch water source, the main pipeline (soft tape) is connected with drip irrigation tape, so that the water in the main pipeline (soft tape) flows into the drip irrigation tape respectively.Usage: use a puncher (14mm in diameter) to make a hole on the side of the soft water tape, and then rotate the three-way into the soft tape hole, tighten the nut to fix the bypass on the soft water tape, and connect the drip irrigation tape on the other sideParameters:Model:16mmMaterial: PE plastic
Contact Now
Purpose: it is usually used in drip irrigation system, when PE soft tape is used as main (branch) pipe, and the soft tape three-way is used as water separation device to connect with drip irrigation tape. That is, the irrigation system uses soft tape as low-pressure water transmission pipeline, and uses soft tape three-way to connect with soft tape , and then connects with drip irrigation tape through the reversed lock-nut on the soft tape three-way, and supplies water to drip irrigation tape of both sides, thus forming rapid and accurate irrigation of water source.
Contact Now
The drip irrigation belt snap tee has the following advantages: 1. There are internal parts such as locking hoop, stepped ring seal ring, etc. The nuts on both sides can be disassembled for assembly and use, which improves the product reuse rate. And the product design is scientific and reasonable, the pipe fittings have high strength, good sealing performance, and no water leakage. 2. The drip irrigation belt positive female snap tee is easy to install and use, easy to disassemble, flexible, easy to recycle, beautiful and practical.
Contact Now
The three-way is pipe fittings and pipe connectors. Also known as pipe three-way or three-way pipe fittings, three-way joint, used in the main pipe to branch pipe.The three-way has three openings, namely one inlet and two outlets; Or a chemical pipe fittings with two inlets and one outlet, there are T-shape and Y-shape with equal diameter orifice or reducing orifice, which are used for the convergence of three same or different pipelines. The main function of three-way is to change the direction of fluid.
Contact Now
Usage: first, use special puncher to punch holes on the side of soft water tape, then rotate the bypass valve of the product into the hole of soft tape, tighten the screw to fix the bypass valve on the soft water tape, and connect the drip irrigation tape on the other side.
Contact Now
The appearance of simple three-way makes the installation of pipe and pipe fittings more convenient and quick in the project. It is made of engineering plastics, corrosion resistant, easy to install and use, and has long service life and economic and practical application.
Contact Now
Instructions for use: Mainly used for capillary head end control (the right end of the pull ring is connected to a 16mm drip tape, which is fixed by the pull ring; the left end is connected to the water delivery main pipe, which can be used for PE pipes (wall thickness greater than 1mm), water delivery tape or use with matching rubber bands , Connect with pvc pipe.)Product introduction: The pull-ring bypass switch is a commonly used drip irrigation switch.
Contact Now
Instructions for use: used for the connection and front-end control of the water delivery belt and the drip irrigation belt (one end of the valve is connected to a 16mm drip irrigation belt, which is fixed by a screw lock; the other end is connected to the main water delivery belt)How to use: First use a hole punch (14mm in diameter) to punch holes on the side of the soft water belt, then rotate the bypass valve of the drip irrigation belt into the hole of the soft belt, tighten the nut to fix the bypass on the soft water belt, and on the other side Just connect the drip tape.
Contact Now
Product features: soft tape bypass valve has its own valve, which can control and adjust the flow of each drip irrigation tape at will.Precautions for installation: 1. mainly used for connection of main water tape, PE water tape(wall thickness 0.6-1.6mm), etc.2.The fittings of this specification are connected between the soft drip irrigation tapes with inner diameter of 16mm.
Contact Now
Product introduction: the pull ring bypass switch is a common drip irrigation switch, one end of which is connected with the main water tape or PE pipe, and the other end is connected with the drip irrigation tape, so as to achieve the effect of controlling the water flow in the rear section of the valve.Instructions for use: it is mainly used for controlling the head end of the capillary (the right end of the pull ring is connected with a 16mm drip irrigation tape, which is fixed by the pull ring; The left end is connected with main water delivery pipe, which can be used for PE pipe (wal
Contact Now
Set combination Multiple combinations can meet your various needsAOne-outlet three small straight drip arrow + single hook One 4/7 to 3/5 single hookOne 3/5 four-way water separatorThree 50cm3/5PVC capillaries Three small straight drip arrowsBOne-outlet three small straight drip arrows + current stabilizer One 2L, 4L, 8L current stabilizerOne 3/5 four-way water separatorThree 50cm3/5PVC capillariesThree small straight drip arrowsCOne-outlet three big straight drip arrow + single hook One 4/7 to 3/5 single hookOne 3/5 four-way&
Contact Now
It can monitor the total injection amount of fertilizer and the instantaneous injection amount of fertilizer in real timeAdjustable instantaneous fertilizer injection (manual adjustment)Real time monitoring of working voltageReal time monitoring and alarm functions of various faults1. EC, PH (including sensor) Fertilizer concentration detection Water pH detection2. Mobile APP (including one-year service fee +.APP signal conversion)3. The automatic fertilizer mixing tank contains a mixing motor4. Weather station, soil moisture5. Automatic partition can reach 256 channels6.
Contact Now
Set combination Multiple combinations can meet your various needsAOne-outlet two small straight drip arrow + single hook One 4/7 to 3/5 single hookOne 3/5 three-way water separatorTwo 50cm3/5PVC capillaries Two small straight drip arrowsBOne-outlet two small straight drip arrows + current stabilizer One 2L, 4L, 8L current stabilizerOne 3/5 three-way water separatorTwo 50cm3/5PVC capillaries Two small straight drip arrowsCOne-outlet two big straight drip arrow + single hook One 4/7 to 3/5 single hookOne 3/5 three-way
Contact Now
Product features: scientific design, high strength, good sealing, convenient connection, easy disassembly, strong flexibility, easy recycling, and beautiful appearance. It is made of engineering plastics and has a long service life.
Contact Now
Product features:Connect 16 / 20mm PE pipe and butt with 16 / 20 mm PE pipeHigh strength product16/20MM socket-typeFunctions: 1. On-off valve 2. Regulating flow 3.
Contact Now
The built-in patch drip irrigation tape has the following characteristics:The built-in patch drip irrigation tape has many kinds of drip hole spacing for customers to choose, and can customize drip irrigation tape with different plant spacing for customers, so as to ensure that the drip irrigation tape meets the requirements of customers for all planting spacing.The outer diameter of the product is 16mm, and the wall thickness is divided into three types: 0.2/0.3/0.4mm (normal working pressure is 0.08MPa-0.1MPa, and the flow rate of emitter is 2L/h). It can b
Contact Now
Micro spray beltBasically put an end to the chance of pests and diseases infestation.
Contact Now
The product has many types, with the characteristics of quick and convenient connection and disassembly, good sealing performance, high strength and long service life. It is widely used in field micro -spray irrigation project.
Contact Now
There are two types of drip irrigation tape lock-nut bypass produced by our factory, one is 12-16mm reversed lock bus bypass, the other is 16-16mm reversed lock-nut bypass. Generally, users call this kind of reversed lock-nut bypass as drip irrigation tape lock-nut bypass. 16-16mm lock-nut bypass is also called large hole lock-nut bypass or large body lock-nut bypass. Because both ends are 16mm diameter, this large hole lock-nut bypass is a kind of bypass that is more commonly used in lock-nut pipe fittings.
Contact Now
Model: Φ16mmMaterial: PEProduct advantages and characteristics:1.Scientific design, compact size, light weight, good sealing and interchangeability.2.Simple structure, convenient operation, quick connection and disassembly, strong flexibility, easy to recycle, beautiful and practical.3.Stable chemical properties, excellent performance, good cold-resistance, anti-aging, long service life.4.Compact size, light weight, good sealing and interchangeability.5.It is suitable for various working conditions and widely used in various media such as gas, liquid, powder, etc.
Contact Now
Good toughness, strong adaptability to terrain, easy laying, long service life, more than 8 years naked on the ground. The connection is convenient, and there are special fast connection fittings.
Contact Now
principle:When the filter is working normally, the pressurized water flows into the tank from the water inlet and reaches the filter layer evenly. When the water flows through the filter layer, the impurities are filtered and retained. There is a water trap with a valve at the bottom of the filter, and the filtered water is collected evenly and then flows out of the filtering equipment.With the continuous accumulation of impurities in the filter layer, the water flow loss continues to increase.
Contact Now